Filtration selection starts with what’s in the air, not with the equipment. A filter sized for welding fume does nothing for a vapour. A unit holding clean air in a control room solves a different problem to one capturing dust at a grinding station.
Fanquip’s filtration range spans fume extractors, filter fans, negative air units and air curtains. Which applies depends on what the contaminant is and how it’s distributed.
Overview.
- Particulate versus vapour: a particle filter does nothing to a gas or vapour.
- Distribution decides the approach: a workstation source and a whole production floor need different equipment.
- Protecting equipment is a separate requirement to protecting people.
- Separation is filtration too: keeping contaminants out of a zone beats removing them from it.
- Filter media creates resistance, which changes the fan the system needs.

What’s in the air decides the equipment.
Particulates are solid matter carried in air: welding and soldering fume, grinding dust, dry dusts, flour, grain. They can be captured on a filter medium, and the finer the particle the finer the filtration required.
Vapours and gases behave differently. They disperse rather than settle, pass straight through a particle filter, and need either extraction to outside air or a different treatment. A site that installs particle filtration against a solvent vapour has spent money without changing the exposure.
Many processes generate both. For the specific question of which extraction approach suits a fume application, choosing the right fume extraction system covers at-source, dilution and ambient in detail.
Fibreglass manufacturing generates both at once.
A fibreglass pool manufacturer works with resins, gelcoats and fibreglass, all of which emit fumes during application and processing. Particulates and vapours together, across a production floor rather than at a single station.
Fanquip’s answer was a filter wall rather than point capture: two 10-metre spray booth filter plenums, each running two direct drive axial fans. The system adapts in size and height to suit the facility. The full project is in extracting fumes and fibreglass particles.
The contrast is instructive. At an industrial cleaning services workshop, a single mobile fume extractor met the extraction need. It runs a metal mesh prefilter for sparks ahead of an F9 cartridge filter, on a 3000mm articulated arm. Same category of contaminant, different distribution, different equipment.
Protecting equipment is a different requirement.
Not all filtration is about worker exposure. Filter fans deliver filtered fresh air into rooms holding sensitive equipment, keeping dust out of switchrooms, control rooms and electrical enclosures.
The filter fan runs GRP adjustable pitch blades and a powder-coated steel casing. It takes a replaceable filter and an IP55 motor, in 240V or 415V. The objective is equipment life and fewer shutdowns rather than compliance, which is why it tends to get overlooked until something fails.
Where clean replacement air has to enter a whole building rather than one room, filtered roof supply fans deliver it through the roof. That suits buildings with no ceiling cavity for conventional filter boxes.
Keeping contaminants out beats removing them.
The cheapest filtration is the contaminant that never enters the space.
Air curtains form a high-velocity air barrier across an opening, blocking dust, odours and insects while holding conditioned air inside. Fanquip’s stainless steel units meet AQIS requirements with a minimum airstream velocity of 8 m/s, IP56 rated, in 900, 1200 and 1500mm widths.
One cold storage site installed five air curtains above every window and door opening, holding temperature while preventing dust, odours and insects entering. That’s separation rather than filtration, but it belongs in the same decision. A loading dock, or a boundary between a dusty area and a clean one, is usually a problem to solve at the opening rather than by filtering the room behind it.

Filter media changes the fan.
Filtration and fan selection aren’t separate decisions. Filter media creates significant static pressure that an axial fan cannot efficiently overcome.
That’s why ducted and filtered systems often require centrifugal fans, which maintain airflow performance under high resistance conditions that would cause an axial fan to stall or deliver substantially reduced volume. A system specified on airflow alone underdelivers from the day it’s commissioned.
It also means adding filtration to an existing system changes what that system can move. A fan chosen before anyone specified the filtration was working to a different resistance.
Which combination suits a site depends on the contaminant, how it’s distributed and what the building allows. That’s a question about the process rather than the product range, so tell Fanquip’s team what the process generates and they can work back to the equipment.
FAQs
Particulates like welding fume and grinding dust can be captured on a filter medium, at the source or through ambient filtration. Vapours and gases pass through particle filters and need extraction or a different treatment.
A fume extractor captures contaminated air at the point of generation and filters it. A filter fan supplies clean filtered air into a room, usually to protect equipment rather than to capture a contaminant.
Yes. Filter media creates significant static pressure that an axial fan cannot efficiently overcome, which is why filtered and ducted systems often need centrifugal fans.
They prevent contaminants entering a space rather than removing them once inside, which suits doorways, loading docks and boundaries between clean and dusty areas.
Filter media loads with captured contaminant, raising system resistance. Airflow falls as a result, even though nothing about the installation has changed.